Midi Amp Selector
| MARK L Custom Guitar Midi AMPLIFIER SELECTOR: |
- Up to 3 amplifiers.
- 6 control swtches for amps use
- Save & silent switching system for amps into the same cabinet or other device
- 1 amp can run at a time
- Impedance matching buffers
- Transformer-isolated inputs for ultra-low noise ratio and ground hum elimination
- MIDI controll via CC (Control Change Commands)
- 2 auxillary line outputs - first as direct out, second as post-poweramp signal
- Handcrafted with a use of a highest quality components - supreme tone clarity guaranteed
MARK L AMPLIFIER SELECTOR
A common problem with a multiple amp set-up of tube amps is how to keep them QUIETLY and to have flexibility in the control. A standard one rack space unit that has three separate transformers to ensure silent switching between any combination of pre-amps, power amps and other effects, with no loss in signal quality to each of the units and connects the amps to a common loudspeaker cabinet.Unused amps are protected, only one amp is allowed to be active at a time. Thus amp switching happens without any line buzz, popping or signal weakness.A rear panel tuner output is also provided, and is active even when no amps are selected.Our gear also has DIRECT OUT - buffered audio OUT for WET/DRY/WET guitar system.It also has LINE OUT (POWERAMP OUT) - ISO separated OUT (with level control) for WET/DRY/WET guitar system.AMP SELECTOR is midi controlled (via Control Change Commands)
FRONT PANEL
The front panel has 11 LED diodes informing which AMPLIFIER (AMP1-AMP3) or which switch (S1-S6) is on, a MIDI light which informs if the device is receiving MIDI signals and MUTE light which informs if the all system MUTE and TUNER on. LINE OUT LEVEL control ( off to -15dbu )To connect to the FC-25 use the lockable XLR6.MIDI-IN SOCKET is equipped with additional power supply thanks to which the FC-25 may be powered by the Amp Selector ( pin 1-2 AC power for FC-25, pin 4-5 MIDI DATA, pin 3-6 12AC power for FC25 DC converter). To connect audio through a high impedance line buffer, connect to the lockable JACK 6,3 mm GUITAR IN
REAR PANEL
The rear panel has 6,3 mm ‘jack’ inputs used for connecting effects, audio signals and control switches for the amplifier and other devices:
- GUITAR IN – Guitar input – same input as on the front panel, use either one or the other
- TUNER OUT - ISO separated TUNER output
- AMP 1 OUT - ISO separated output for AMP 1
- AMP 1 SPEAKER IN - Connect to Amp 1 from speaker out jack.
- AMP 2 OUT - ISO separated output for AMP 2
- AMP 2 SPEAKER IN - Connect to Amp 2 from speaker out jack.
- AMP 3 OUT - ISO separated output for AMP 3
- AMP 3 SPEAKER IN - Connect to Amp 3 from speaker out jack
- SPEAKER OUT - to load speaker
- DIRECT OUT - buffered audio OUT
- LINE OUT - ISO separated OUT with Level Control ( POWERAMP OUT )
- SWITCH 1- 6 - used for controlling the amplifier channels, etc.
- GND/LIFT - chassis ground lift switch
- MIDI IN - used for communication with a midi controller
- MIDI OUT THRU - MIDI signal used for additional devices
- MIDI CHANNEL - switch used for switching channel from 1 to 16
- POWER IN - power supply socket for AC 9V/1000mA (AC Plug 2,5mmx5,5mm)
- EXT POWER IN - for AC power converter 12VAC /250mA (AC Plug 2,5mmx5,5mm)
Warranty 2 years
| TECHNICAL SPECIFICATION: | |
| Power In: Operational temperature: Height: Width: Length: Weight: |
Power supply socket for AC 9VAC/1A Plug 2,5 mm x 5,5 mm |
PRICE: 899,00 € Include VAT23%
Ships within 10-20 days
